Call 08042901475 71% Response Rate

Send Email

Bituminous & Synthetic Primer

Providing you the best range of shalitex primer and shaliprime pw ct synthetic primer with effective & timely delivery.
ShaliTex Primer

ShaliTex Primer

Product Price: Rs 215 / LitreGet Best Price

Product Brochure

Product Details:
BrandShaliTex
Water Content0.20 %
Service Temperature5 - 50 Degree C
Specific Gravity0.90
ConsistencyBrushable & Sprayable
Shelf Life12 months in original unopened sealed conditions
Flash Point40 Degree C Min
Theoretical Coverage0.30 L / m2
Country of OriginMade in India
StorageKeep in cool and dry place,in air tight container,under shed,away from heat.
Packing20 L drum
Setting Time at Ambient Temperature24 Hours
ShaliTex Primer is a solvent based bituminous primer that seals pores in surfaces such as concrete and improves the adhesion of bituminous materials that are to be applied to the substrate. It is suitable for brush or spray application. It conforms to the requirement of IS: 3384-1986.

Application:
  • Priming bituminous, concrete / metal surfaces prior to laying membrane promotes bonding, whether self-adhesive or otherwise. 
  • Applied in canal lining joints and concrete floor joints prior to pouring of the bitumen sealing compound for bonding.  

Advantages:
  • Seal pores on surfaces such as concrete
  • Improves the adhesion of bituminous material that is to be applied to the substrate.

Application Methodology:
  • Ensure not to apply when temperature is less than 5 OC or during foggy period
  • Before applying the primer make the concrete surfaces free from dust and sand particles by brooming and allow it to dry. Concrete should be cured and should be eight days old.
  • ShaliTex Primer should be thoroughly stirred before use and applied to the substrate by means of brush, roller or spray at the rate of 0.30 L/m2 .
  • Allow it to dry for 24 hr. 

Health & Safety:
  • Avoid contact with skin / eyes and avoid swallowing
  • Ensure adequate ventilation and avoid inhalation of vapor
  • Wear suitable protective clothing, gloves and eye protection 
  • In case of contact with skin, rinse with plenty of clean water, then cleanse with soap and water. Do not use solvent to clean the contacted area
  • In case of eye contact, wash immediately with plenty of clean water and seek medical advice
  • If swallowed seek medical attention immediately. Do not induce vomiting

Other Packing: 200 L
Get Best QuoteRequest Callback
ShaliPrime PW CT Synthetic Primer

ShaliPrime PW CT Synthetic Primer

Product Price: Rs 235 / KgGet Best Price

Product Brochure

Product Details:
BrandShaliPrime
Theoretical Coverage8 - 10 m2 / L
Shelf Life12 months in unopened sealed condition
StorageKeep in cool and dry place, under shed, away from heat
Packing20 L steel drum
Specific Gravity at 30 Degree C1.00 - 1.10
Flash Point (Abel) Degree C23
Viscosity (Flow Time), 20 Degree C, No. 4 Flow cup, sec35 - 60
DFT Micron30 +- 5
Volatile Matter, 100-110 Degree C, Loss of Mass, %75 Max
Drying Time Minutes Tack Free5 - 15
ApplicableBy Brush / Spray
ShaliPrime® PW CT is resin based synthetic primer containing unmodified chlorinated rubber and special grade of coal tar pitch. It is applied without heating and produces an effective bond between the surface to be protected and Coal Tar Tape wrapped thereon.

It conforms to AWWA C 203 : 2015, IS 10221 and IS 15337 : 2003 and EIL Specification.

Application:
  • ShaliPrime® PW CT is applied as a primer over steel pipelines for providing bond between PipeWrap CT and primed steel pipes

Surface Preparation:
  • Clean the surface free of all foreign matter, dust, oil or grease, specially of chloride contamination. 
  • Ensure not to apply when temperature is less than 5
  • Blast clean surface of the pipe by shot and grit to a greyish matt appearance to SA 2 ½.

Application of Material:
  • Apply ShaliPrime PW® CT at the rate of 0.30 L / m2 on completely dry surface

Health & Safety:
  • Avoid contact with skin / eyes and avoid swallowing
  • Ensure adequate ventilation and avoid inhalation of vapour
  • Wear suitable protective clothing, gloves and eye protection
  • In case of skin contact, rinse with plenty of clean water, then cleanse with soap and water. Do not use solvent to clean the contacted area
  • In case of eye contact, wash with plenty of clean water and seek medical advice. 
  • If swallowed, seek medical attention immediately. Do not induce vomiting

Other Packing: 200 L 
Get Best QuoteRequest Callback

EXPLORE MORE CATEGORIES

Looking For "Bituminous & Synthetic Primer"?
Thank youYour Enquiry has been sent successfully.
© STP LIMITED. All Rights Reserved (Terms of Use)Developed and managed by IndiaMART InterMESH Ltd.