- Home
- ยป
- Our Products
- »
- Waterproofing Membrane
Waterproofing Membrane
Manufacturer of a wide range of products which include superthermolay app modified waterproofing membrane, tarfelt app pliable membrane, tarfelt lm water based bituminous liquid membrane, shaliurethane lhm 2k polyurethane waterproofing membrane, supertene sbs modified self adhesive membrane and shaliurethane btd elastomeric pu liquid membrane.
SuperThermoLay APP Modified Waterproofing Membrane
Product Price: Rs 5,100 / RollGet Best Price
Product Brochure
Product Details:
Brand | SuperThermoLay |
Packing | For 2 mm - 1 m x 15 m |
Penetration @ 25 Degree C (3 & 4 mm) | 25 +- 5 |
Softening Point (5 mm and above) | Greater than or equal to 150 Degree C |
Cold Flexibility | 2 Degree C (Below 3 mm, 3 & 4 mm, 5 mm and above) |
Storage | Keep in cool and dry place, under shed, away from heat. |
Penetration @ 25 Degree C (Below 3 mm) | 15 +- 5 |
Penetration @ 25 Degree C (5 mm and above) | 25 +- 5 |
Softening Point (Below 3 mm) | Greater than or equal to 145 Degree C |
Softening Point (3 & 4 mm ) | Greater than or equal to 150 Degree C |
Water Absorption | 0.2% (Below 3 mm, 3 & 4 mm, 5 mm and above) |
SuperThermoLay forms an impervious, flexible waterproofing layer which can withstand normal movement of structure without showing any deterioration and serve for a prolonged period of time.
SuperThermoLay is normally used in protected roofing and waterproofing applications in a single layer system and is also recommended as base layer in multilayer system in various applications, including damp-proofing.
SuperThermoLay with cold flexibility up to 2 OC is supplied in following variants:
- Plain finish with thermo-fusible polyethylene film on both surfaces,
- Mineral / natural grey slate finish with thermo-fusible polyethylene film on one surface, and mineral / natural gray slate on the other surface.
Application:
- SuperThermoLay membranes are ideal for a wide range of waterproofing applications including roofs, reservoirs, basements, basement roof, sunken slabs, terrace garden, car parking, tunnels and bridge decks.
Advantages:
- Total impermeability
- Excellent resistance to ageing and weathering
- Outstanding bond-ability and seam integrity
- Stability at high temperatures
- High resistance to impact and puncture.
- Simple, single-layer installation reduces labour and error
- Excellent cold flexibility.
Surface Preparation:
- Remove all loose gravel, dirt, oil, grease and foreign matter by jet of dry air and clean the surface mechanically or by grinding to make it smooth before application
- Ensure that the moisture content in the prepared surface does not exceed 5%
- Correct all construction joints by grouting with ShaliGrout IP at 1 m apart and opening of joints in “V” cut groove and fill with ShaliFix RM C, using ShaliSBR Latex as the bond coat.
- Build-up gradient minimum 1 in 100 with PCC admixed with ShaliPlast LW +.
- Ensure that level of all drain mouth is lower than deck slab level by at least 15 mm
- Provide 75 mm x 75 mm coving made out of PCC admixed with ShaliPlast LW + and using ShaliSBR Latex as bond coat
Packing: For 3 / 4 / 5 mm - 1 m x 10 m
Specifications:
Property | Standard | Below 3 mm | 3 & 4 mm | > 5 mm |
Tensile / Lap Joint Strength, N / 5 cm Longitudinal Transverse |
ASTM D-5147 | >250 >120 |
650 ± 150 450 ± 100 |
650 ± 150 450 ± 100 |
Tearing Strength, N Longitudinal Transverse |
ASTM D-5147 | >250 >90 |
300 ± 100 250 ± 100 |
400 ± 100 400 ± 100 |
Elongation, % @ 23 OC Longitudinal Transverse |
ASTM D-5147 | >30 >30 |
40 ± 10 50 ± 10 |
40 ± 10 50 ± 10 |
Puncture Resistance, N Static Indentation |
IS 13826 | 230 ± 40 | 280 ± 20 | 300 ± 20 |
Get Best QuoteRequest A Callback
TarFelt APP Pliable Membrane
Product Price: Rs 6,100 / RollGet Best Price
Product Brochure
Product Details:
Brand | TarFelt |
Packing | Rolls are available in 1 m x 20 m in 1.5 & 2 mm thicknesses |
Longitudinal Elongation @ Break | > 30% (ASTM D-5147) |
Longitudinal Tensile Strength | > 250 N/5 cm (ASTM D-5147) |
Transverse Tensile Strength | > 120 N/5 cm (ASTM D-5147) |
Storage | Keep in cool and dry place, under shed, away from heat |
Softening Point | > 145 Degree C |
Penetration @ 25 Degree C | 15 +- 5 dmm |
Transverse Elongation @ Break | > 30% (ASTM D-5147) |
Transverse Tearing Strength, N/7.5 cm | > 90 (ASTM D-5147) |
Longitudinal Tearing Strength N/7.5 cm | > 250 (ASTM D-5147) |
- TarFelt APP is uniquely formulated, cold applied, pre-fabricated, economic elastomeric waterproofing membrane with non-woven polyester mat core.
- TarFelt APP forms an impervious, flexible waterproofing layer which can withstand normal movement of structure without showing any deterioration and serve for a prolonged period of time.
- TarFelt APP is normally used in protected roofing and waterproofing applications in a single layer system and is also recommended as base layer in multilayer system in various applications, including damp-proofing.
- TarFelt APP may, if so desired, be applied with hot bitumen of 30/40 grade after removing the release film. However, for application with hot bitumen, as aforesaid, TarFelt® APP is also produced without release film and is recommended for such application as it is slightly cheaper without any compromise on its characteristics. Bitumen Grade 85/25 or 90/15 shall be used for vertical surface.
Application:
- Waterproofing of corrugated asbestos / metal sheets, Basement / retaining walls in low water pressure area, Residential roofs / podiums.
- As base layer in multi-layer waterproofing system
- As virtual self-adhesive waterproofing membrane in combination with ShaliBond APP and can be applied to the surface without any torching or heating.
- As DIY (Do-It-Yourself) and repair product.
Advantages:
- Total impermeability.
- Excellent resistance to ageing and weathering.
- Outstanding bond-ability and seam integrity.
- Stability at high temperatures.
- Very high resistance to impact and puncture.
- Simple, single-layer installation reduces labour and error.
- Good cold flexibility
Surface Preparation:
- Remove all loose gravel, dirt, oil, grease and foreign matter by jet of dry air and clean the surface mechanically or by grinding to make it smooth before application.
- Ensure that the moisture content in the prepared surface does not exceed 5%.
- Correct all construction joints by grouting with ShaliGrout IP at 1 m apart and opening of joints in “V” cut groove and fill with ShaliFix RM C, using ShaliSBR Latex as the bond coat.
- Build-up gradient minimum 1 in 100 with PCC admixed with ShaliPlast LW +.
- Ensure that level of all drain mouth is lower than deck slab level by at least 15 mm.
- Provide 75 mm x 75 mm coving made out of PCC admixed with ShaliPlast LW + and using ShaliSBR Latex as bond coat.
Waterproofing Application:
- Apply ShaliBond APP uniformly on the substrate, approx. @ 3 m2 / kg (theoretical, depend upon surface condition) by trowel / brush and allow the solvent to evaporate. Unroll TarFelt® APP over the tacky surface and bond it to the surface by applying uniform pressure. This makes TarFelt® APP virtual self-adhesive membrane.
- For overlapping of joints, rub the polyethylene side of the membrane by wire brush, apply ShaliBond APP over the rubbed area, allow it to be tacky and then affix bituminous side of the TarFelt
- For longitudinal and transverse joints overlap of 75 mm and 100 mm respectively is desired.
- Alternatively, apply TarFelt® APP with hot bitumen 30/40 grade @ 800 grm / m2 with Pour & Roll Method in horizontal surface and bitumen 30/40 grade @ 600 grm / m2 in vertical surface.
- Cut 1” deep grove 300 - 450 mm above the roof surface on the parapet wall and seal the edge of TarFelt® APP inside the groove with polymer modified mortar. In case of low height parapets, terminate TarFelt® APP over the parapet.
- Allow 3-4 days for full dry.
- Seal all the corners of membrane with the ShaliBond APP / STP make 30/40
Get Best QuoteRequest A Callback
TarFelt LM Water Based Bituminous Liquid Membrane
Product Price: Rs 230 / KgGet Best Price
Product Brochure
Product Details:
Brand | TarFelt |
Packaging Size | 20 Kg |
Theoretical Coverage | 1.6 m2 / mm DFT, Kg |
Water Absorption | < 1% |
Specific Gravity @ 30 Degree C | 1.0 +- 0.01 |
Crack Bridging Maximum | 0.8 mm (ASTM C-836 ) |
Appearance | Viscous emulsion dries to black coating |
Drying Condition | 40 min for each coat depending on climatic condition |
Elongation After 7 Days (1.50 mm Film) | 190 - 200% (ASTM C-412) |
Tensile Strength After 7 Days (1.50 mm Film) | 0.50 MPa (ASTM C-412) |
Storage | Store in a cool dry place, under shed, away from heat |
Shelf Life | 12 months in original unopened sealed condition |
Application Temperature | > 5 Degree C |
Viscosity on Brookfield @ 25 Degree C, CPS | 1600 - 1800 |
Pull Off Adhesion | 1.2 MPa (ASTM D-4541) |
- Corrugated asbestos / metal / non-galvalised corrugated tin roofs
- Sunken
- Rejuvenation of existing bituminous membrane – Hessian / HMHDPE based membrane
- Residential terraces (flat / slope) in substitution of hessian / HMHDPE based membrane
Advantages:
- User friendly, Non-toxic, Green product.
- Excellent Waterproofing Characteristics.
- Good crack bridging property
- Cold applied and hence does not require heating
- Monolithic and Seamless Membrane
- Excellent bonding to concrete
- Can be applied on moist surface also
- Excellent vapour barrier
- Good flexibility and does not crack on aging
- Prevents growth of fungus, algae etc
Application Methodology Surface Preparation:
- Remove all loose gravel, dirt, oil, grease and foreign matter by jet of dry air and clean the surface mechanically or by grinding to make it smooth before application
- Repair all cracks by cutting “V” groove and fill with PMC mortar prepared in the ratio of ShaliCrete : Cement : Sand (1 : 2 : 5)
- Provide 50 mm x 50 mm coving made out of PMC mortar as above.
Material Preparation:
- Stir TarFelt LM by a slow speed mixture (approx. 400 rpm) fitted with a suitable mixing paddle to ensure a homogenous mix
- After stirring, wait for the product to settle in order to let entrapped air escape
Waterproofing Application:
- Slightly damp the surface. Avoid standing water / ponding
- Prime the surface with a mixture of TarFelt LM and potable water in the ratio of 50 : 50 and apply @ 400 grm / m2 of the mixture and allow it to touch dry
- Apply first coat of TarFelt LM @ 0.70 kg / m² by brush / roller / airless spray while the primed surface is tacky. For faster and smoother application, airless spray is preferred
- Spread fiber glass net of 45 gsm with overlaps of 50 mm in both directions when the surface is still tacky
- Allow 1st coat to dry for 10 – 12 hr
- Apply second coat of TarFelt LM @ 0.70 kg / m² by brush / roller / airless spray for final DFT of 1000 micron in two coats inclusive of fiber glass of 45 gsm (theoretical coverage depending on surface conditions)
- Sprinkle sand @ 200 grm / m2 over the final vertical coating when the surface is still tacky to facilitate plastering
- Ensure final curing time of 36 hrs before allowing / carrying out any further work
- Conduct ponding test after 7 days of curing at ambient temperature
Protection of Waterproofing:
- Spread ShaliGeoText 150 gsm with overlap of 50 mm in both directions on fully cured surface
- Protect surface with 50 mm PCC admixed with ShaliPlast LW+ and a gradient of 1 : 100.
Rejuvenation of Existing Treatment:
- Clean existing surface thoroughly and remove all loose / foreign material
- TarFelt LM shall be applied on prepared surface as per above procedure
Health & Safety:
- Avoid contact with skin / eyes and avoid swallowing
- Ensure adequate ventilation and avoid inhalation of vapor
- Wear suitable protective clothing, gloves and eye protection
- In case of contact with skin, rinse with plenty of clean water, then cleanse with soap and water. Do not use solvent to clean the contacted area.
- In case of eye contact, wash immediately with plenty of clean water and seek medical advice
- If swallowed seek medical attention immediately. Do not induce vomiting.
Get Best QuoteRequest A Callback
ShaliUrethane LHM 2K Polyurethane Waterproofing Membrane
Product Price: Rs 565 / KgGet Best Price
Product Brochure
Product Details:
Brand | ShaliUrethane |
Solid Content | 90 +- 2 |
Pot Life @ 27 OC, RH 60%, Minutes | 60 +- 10 |
Storage | Store in a cool dry place under shed away from heat |
Intermittent Service Temperature | Up to 160 Degree C |
Tensile Strength | 2.2 +- 0.5 MPa ASTM D-412 |
Tear Strength | > 28 MPa (ASTM D-624) |
Shelf Life | 6 months in original unopened sealed condition |
Composition | Polyurethane resin and Catalyst |
Theoretical Coverage kg / m 2, 1 mm DFT | 1.46 |
Hardness (Shore A) | 40 +- 5 (ASTM D-2240) |
Packing | Available in 26 kg pack consisting of Component A 25 kg and Component B 1 kg |
Tack Free Time | 2 +- .5 Hours |
Re-Coat Time | 6 - 8 hrs |
Mixing Ratio | Unit Pack |
Continuous Service Temperature | -) 40 to (+) 120 Degree C |
Trafficable Time | After 24 Hours |
Water Absorption | < 0.5% (ASTM D-471) |
Elongation at Break | 400 +- 50% ASTM D-412 |
It conforms to ASTM C836 and C 898.
Application:
- Bridge deck waterproofing.
- Roofs and terraces.
- Podium.
- Retaining Walls.
- Swimming Pool.
- Tunnels.
Advantages:
- Easy to apply.
- Medium tensile.
- Excellent crack bridging properties Blister free coating. No appearance of holes in the surface during the curing of material
- Prevents moisture penetration, provide complete sealing and anti-corrosion to the metal surface.
- Excellent bonding to all building substrates like concrete, plaster, metal, wood.
- Resistant to water, frost, mild acid and alkali.
Surface Preparation:
- Remove all loose gravel, dirt, oil, grease and foreign matter by jet of dry air and clean the surface mechanically or by grinding to make it smooth before application.
- Repair all cracks by cutting “V” groove and fill with PMC mortar prepared in the ratio of ShaliCrete : Cement : Sand (1 : 2 : 5).
- Correct honeycomb / other minor surface defects with PMC mortar using ShaliSBR Latex as the bond coat.
- Ensure provision of slope in the gradient of 1 : 100 towards drain by laying PCC admixed with integral waterproofing compound, ShaliPlast LW+ @ 200 ml / bag of cement preferably with galvanised chicken wire mesh.
- Provide fillet 75 mm x 75 mm coving made out of PMC mortar as above, using ShaliSBR Latex as bond coat.
- Ensure that the moisture content in the prepared surface does not exceed 5% immediately before application of ShaliUrethane LHM 2K.
Material Preparation:
- Skin formation may happen on the top of material during humid condition. In that event, cut skin from the periphery of the container and remove it.
- Stir ShaliUrethane LHM 2K by a slow speed mixture fitted with a suitable mixing paddle to ensure a homogenous mix.
- After stirring, wait for the product to settle in order to let entrapped air escape.
- Use the entire material within 4 hours of opening the container
Waterproofing Application:
- Prime the surface with In case anti-root property is desired, tar extended anti-root primer-cum-sealer, ShaliPrime WP SB @ 400 grm / m2 or In other cases, ShaliPrime PUM @ 8 – 10 m2 / L
- Allow the primer to touch dry condition.
- Apply 1st coat of ShaliUrethane LHM 2K @ 730 grms / m2 by brush / roller / airless spray while the primed surface is tacky. For faster and smoother application, apply with airless gun
- Spread non-woven geo-textile of 40 / 50 gsm with overlaps of 50 mm in both directions when the surface is still tacky; this is optional, to be assessed as per site requirements to achieve higher mechanical properties
- Allow 1st coat to dry for 10 – 12 hr.
- Apply 2nd coat of ShaliUrethane LHM 2K @ 730 grms / m2 by brush / roller / airless sprayEnsure final curing time of 36 hrs before allowing / carrying out any further work.
- Extend waterproofing treatment up to 200 mm and terminate into groove on the parapet wall. Fill the groove with PMC mortar
- In case of vertical application, protect the applied liquid membrane, By sprinkling sand @ 200 grm / m2 over the final coating when the surface is still tacky to facilitate plastering, and 25 mm plaster admixed with ShaliPlast LW + @ 200 ml / bag of cement
- In case of horizontal surface, protect the applied liquid membrane, Preferably with ShaliUrethane WB HA, high abrasion resistance liquid coating which can take foot traffic
Get Best QuoteRequest A Callback
SuperTene SBS Modified Self Adhesive Membrane
Product Price: Rs 4,900 / RollGet Best Price
Product Brochure
Product Details:
Brand | SuperTene |
Cold Flexibility | -18 Degree C |
Compound Elongation | > 200% ASTM D-638 |
Adhesion to | Primed Concrete 2.3 N / mm, Other Surfaces 2.0 N / mm (ASTM D-1000) |
Puncture Resistance | 260 N ASTM E-154 |
Shelf Life | 12 months in original unopened sealed conditions |
Packing | Available in two widths of 1 m x 20 m Roll. |
Total Thickness | 1.5 / 2.0 mm |
Service Temperature | -5 / +55 Degree C |
Moisture Vapour Transmission Rate | < 0.30 grm /m2 / hrs, ASTM E-96 |
Application:
- Highly recommended for waterproofing / damp-proofing of vertical foundation / walls.
- Waterproofing of structural concrete and masonry walls, pitch roof split slab concrete construction, both above and below ground.
- Waterproofing of Insulated roofs, wet areas like bathrooms, kitchens etc., parking areas, balconies, terraces, windows, garages.
- Waterproofing in general at all such place where the use of fire is not possible or is prohibited.
Advantages:
- Cold applied, does not require heat, chemical bonding agents or special tools.
- Easy and quick installation.
- Permanent flexibility and protection.
- Effective water and vapour barrier.
- Strong resistance to chemicals like chlorides, sulphates, alkalis, dilute acids, ozone and atmospheric pollutants.
Application Methodology Surface Preparation:
- Remove all loose gravel, dirt, oil, grease and foreign matter by jet of dry air and clean the surface mechanically or by grinding to make it smooth before application.
Application of Material:
- Prime the concrete substrate with ShaliTex Primer. Primer is not necessary for nonporous / non-absorbent surface
- Place the membrane on the primed surface and remove the film by peeling of the release paper not more than 30 cms at a time, while unrolling SuperTene
- Press down the membrane from the middle to the outer edges. This will help to remove any entrapped air ensuring good adhesion to the substrate
- SuperTene should always be protected to avoid damage caused by other trades, backfilling equipment and materials. Screeds, toppings and tiles should be laid as soon as possible, preferably the same day the membrane is applied. Under no circumstances should the membrane be left exposed for extended period.
Health & Safety:
- Avoid contact with skin / eyes and avoid swallowing.
- Ensure adequate ventilation and avoid inhalation of vapour.
- Wear suitable protective clothing, gloves and eye protection.
- In case of skin contact, rinse with plenty of clean water, then cleanse with soap and water. Do not use solvent to clean the contacted area.
- In case of eye contact, wash with plenty of clean water and seek medical advice.
- If swallowed, seek medical attention immediately. Do not induce vomiting.
Storage:
- Rolls must be stored in dry place, protected from rain, sun ray, heat
- keep in upright position on the dry surface/pallet
- Don’t stack more than two rolls height.
Get Best QuoteRequest A Callback
ShaliUrethane BTD Elastomeric PU Liquid Membrane
Product Price: Rs 430 / KgGet Best Price
Product Brochure
Product Details:
Brand | ShaliUrethane |
Color | White / Terracotta / Green |
Solid Content | > 80% |
Service Temp. Range | - 20 to + 100 Degree C |
Theoretical Coverage For 1.0 mm | 1.85 DFT, Kg / m2 |
Theoretical Coverage For 1.2 mm | 2.20 Kg / m2 |
ShaliUrethane BTD is UV resistant. However, for better UV resistance, we recommend use of White colour BTD, having SRI Index > 109, thus facilitating considerable saving in energy
ShaliUrethane BTD forms a seamless monolithic membrane and can be applied on moist surface
It conforms to ASTM C 836 and ASTM D 6083.
Use Horizontal / Vertical grade of ShaliUrethane BTD for horizontal / vertical application respectively.
Application:
- Roof / Terraces, including corrugated roof Podium
- Refurbishment of APP / SBS / TarFelt roof
- Gutter waterproofing.
Advantages:
- White ShaliUrethane BTD has excellent SRI of 109, thus facilitates energy saving and provides good cooling effect under the treated surface.
- White ShaliUrethane BTD is recommended for all slope roofs and not trafficable roofs, which needs no protection
- Can be applied on moist surface also
- Excellent water vapour barrier
- High Crack Bridging
- Monolithic / seamless / breathable in-situ Membrane
- Excellent adhesion to concrete
- Excellent elongation and very good low temperature flexibility.
Surface Preparation:
- Remove all loose gravel, dirt, oil, grease and foreign matter by jet of dry air and clean the surface mechanically or by grinding to make it smooth before application
- Repair all cracks by cutting “V” groove and fill with PMC mortar prepared in the ratio of ShaliCrete : Cement : Sand (1 : 2 : 5)
- Provide 75 mm x 75 mm coving made out of PMC mortar as above, using ShaliSBR Latex as bond coat
- Ensure gradient of 1 : 100 towards drain by laying PCC admixed with integral waterproofing compound, ShaliPlast LW+ @ 200 ml / bag of cement preferably with galvanised chicken wire mesh
- Ensure that there is no standing water on the applicable surface.
Material Preparation:
- Stir ShaliUrethane BTD by a slow speed mixture fitted with a suitable mixing paddle to ensure a homogenous mix
- After stirring, wait for the product to settle in order to let entrapped air escape.
Waterproofing Application:
- Slightly damp the surface. Avoid standing water / ponding
- Prime the surface In case anti-root property is desired, Use ShaliPrime WP WB @ 200 grm / m2 or In other cases use ShaliPrime BTD at 400 grm / m2
- Allow the primer to touch dry condition.
- Apply 1st coat of ShaliUrethane BTD at 1 Kg / m2 by brush / roller / airless spray while the primed surface is tacky. For faster and smoother application, apply with airless gun
- Spread non-woven geo-textile or Fibre Glass Tissue / scrimp of 45 gsm with overlaps of 50 mm in both directions when the surface is still tacky; this is optional, to be assessed as per site requirements to achieve higher mechanical properties
- Allow 1st coat to dry for 10 – 12 hr
- Apply 2nd coat of ShaliUrethane® BTD @ 1 kg / m² by brush / roller / airless spray for final DFT of 1500 micron in two coats
- Ensure final curing time of 36 hrs before allowing / carrying out any further work
- Extend waterproofing treatment up to 200 mm and terminate into groove on the parapet wall. Fill the groove with PMC mortar with ShaliSBR Latex
Get Best QuoteRequest A Callback
Non Reinforced ShaliEPDM
Product Price: Rs 500 / RollGet Best Price
Get Best QuoteRequest A Callback
Reinforced ShaliEPDM
Product Price: Rs 650 / Square MeterGet Best Price
Get Best QuoteRequest A Callback